ADT7461AARMZ-R【PDF 10/19 页】IC TEMP SENSOR DGTL 2CH 8-MSOP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录39

6页 7页 8页 9页 [10页]11页 12页 13页 14页

ADT7461A

http://onsemi.com

Table 9. CONFIGURATION REGISTER BIT

ASSIGNMENTS

Bit

Name

Function

Power-On

Default

MASK1

0 = ALERT

Enabled

1 = ALERT

Masked

RUN/STOP

0 = Run

1 = Standby

ALERT

THERM2

0 = ALERT

1 = THERM2

4, 3

Reserved

Temperature

Range Select

0 = 0癈 to 127癈

1 = Extended Range

1, 0

Reserved

Conversion Rate Register

The conversion rate register is Address 0x04 at read and

Address 0x0A at write. The lowest four bits of this register

are used to program the conversion rate by dividing the

internal oscillator clock by 1, 2, 4, 8, 16, 32, 64, 128, 256,

512, or 1024 to give conversion times from 15.5 ms

(Code 0x0A) to 16 seconds (Code 0x00). For example, a

conversion rate of eight conversions per second means that

beginning at 125 ms intervals, the device performs a

conversion on the internal and the external temperature

channels.

The conversion rate register can be written to and read

back over the SMBus. The higher four bits of this register are

unused and must be set to 0. The default value of this register

is 0x08, giving a rate of 16 conversions per second. Use of

slower conversion times greatly reduces the device power

consumption.

Table 10. CONVERSION RATE REGISTER CODES

Code

Conversion/

Second

Time (Seconds)

0x00

0.0625

0x01

0.125

0x02

0.25

0x03

0.5

0x04

0x05

500 m

0x06

250 m

0x07

125 m

0x08

62.5 m

0x09

31.25 m

0x0A

15.5 m

0x0B to 0xFF

Reserved

Limit Registers

The ADT7461A has eight limit registers: high, low, and

THERM

temperature limits for both local and remote

temperature measurements. The remote temperature high

and low limits span two registers each, to contain an upper

and lower byte for each limit. There is also a THERM

hysteresis register. All limit registers can be written to, and

read back over, the SMBus. See Table 14 for details of the

limit register addresses and their power-on default values.

When Pin 6 is configured as an ALERT

output, the high

limit registers perform a > comparison, while the low limit

registers perform a d comparison. For example, if the high

limit register is programmed with 80癈, then measuring

81癈 results in an out-of-limit condition, setting a flag in the

status register. If the low limit register is programmed with

0癈, measuring 0癈 or lower results in an out-of-limit

condition.

Exceeding either the local or remote THERM

limit asserts

THERM

low. When Pin 6 is configured as THERM2

exceeding either the local or remote high limit asserts

THERM2

low. A default hysteresis value of 10癈 is

provided that applies to both THERM

channels. This

hysteresis value can be reprogrammed to any value after

powerup (Register Address 0x21).

It is important to remember that the temperature limits

data format is the same as the temperature measurement data

format. Therefore, if the temperature measurement uses

default binary, then the temperature limits also use the

binary scale. If the temperature measurement scale is

switched, however, the temperature limits do not

automatically switch. The user must reprogram the limit

registers to the desired value in the correct data format. For

example, if the remote low limit is set at 10癈 with the

default binary scale, the limit register value is 0000 1010b.

If the scale is switched to offset binary, the value in the low

temperature limit register needs to be reprogrammed to

0100 1010b.

Status Register

The status register is a read-only register at Address 0x02.

It contains status information for the ADT7461A.

When Bit 7 of the status register is high, it indicates that the

ADC is busy converting. The other bits in this register flag the

out-of-limit temperature measurements (Bit 6 to Bit 3, and

Bit 1 to Bit 0) and the remote sensor open circuit (Bit 2).

If Pin 6 is configured as an ALERT

output, the following

applies: If the local temperature measurement exceeds its

limits, Bit 6 (high limit) or Bit 5 (low limit) of the status

temperature measurement exceeds its limits, then Bit 4

(high limit) or Bit 3 (low limit) asserts. Bit 2 asserts to flag

an open circuit condition on the remote sensor. These five

flags are NORed together, so if any of them is high, the

ALERT

interrupt latch is set and the ALERT

output goes

low.

Reading the status register clears the five flags, Bit 6 to

Bit 2, provided the error conditions causing the flags to be

set have gone away. A flag bit can be reset only if the

corresponding value register contains an in-limit

measurement or if the sensor is good.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

我的联系方式

相关代理商/技术参数

ADT7461AARMZ-REEL 功能描述:IC SENSOR TEMP DGTL 2CH 8-MSOP RoHS:是类别:集成电路 (IC) >> PMIC - 热管理系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器）传感器类型:内部和外部感应温度:-40°C ~ 125°C，外部传感器精确度:±2.5°C 本地（最大值），±5°C 远程（最大值）拓扑:ADC，比较器，寄存器库输出类型:2 线 SMBus? 输出警报:无输出风扇:无电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6

ADT7461AARMZ-REEL7 功能描述:IC SENSOR TEMP DGTL 2CH 8-MSOP RoHS:是类别:集成电路 (IC) >> PMIC - 热管理系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器）传感器类型:内部和外部感应温度:-40°C ~ 125°C，外部传感器精确度:±2.5°C 本地（最大值），±5°C 远程（最大值）拓扑:ADC，比较器，寄存器库输出类型:2 线 SMBus? 输出警报:无输出风扇:无电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6

ADT7461AARMZ-RL7 功能描述:板上安装温度传感器 1 TMP DIO MON W/SMBUS ITF RoHS:否制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor

ADT7461AEBZEVB 功能描述:BOARD EVAL FOR ADT7461 RoHS:是类别:编程器，开发系统 >> 过时/停产零件编号系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB）传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否已供物品:成像器板已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP

ADT7461AR 功能描述:IC TEMP MONITOR +/-1C DUAL 8SOIC RoHS:否类别:集成电路 (IC) >> PMIC - 热管理系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器）传感器类型:内部和外部感应温度:-40°C ~ 125°C，外部传感器精确度:±2.5°C 本地（最大值），±5°C 远程（最大值）拓扑:ADC，比较器，寄存器库输出类型:2 线 SMBus? 输出警报:无输出风扇:无电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6

ADT7461ARM 制造商:Rochester Electronics LLC 功能描述:+/-1C TDM SRC EXT TEMP RANGE I.C. - Bulk 制造商:Analog Devices 功能描述:IC TEMP SENSOR

ADT7461ARM2-2 制造商:Analog Devices 功能描述:

ADT7461ARM-REEL 制造商:Rochester Electronics LLC 功能描述:+/-1C TDM SRC EXT TEMP RANGE I.C. - Tape and Reel

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式